Thanks ALL, I will be heading back to Lithuania in a few weeks, and will try to contact him from there. If not I am going to try to find the closest pump and retrofit! All the best! Ken Aquarius SM2K2

All, I have a Eumenia Mini 5500 Dishwasher, and would like keep Aquarius stock. But, need to get spare parts for the dishwasher. I have emailed ersatzteile@schabauer-service dot at , but have not rece

On Aquarius we put her in Reverse to lock the shaft. Would Chris be able to do this? Or will it damage the transmission? Ken Aquarius

Hello Courtney, Chris is still having a problem. Please write more about the procedure to correct the problem, I can't understand how to correct the problem. Is your comment is missing punctuation. "S

I don't know how the cost could come down too much more... I got 600AH at 24V for $3600. The only thing I regret is not getting one more battery so I would have 900AH at 24V. The price has come down s

Jose, The O rings might look good, but still a good idea to change them out if you haven't already done so. Make sure you put a lot of grease on the shaft before you put it back in the hole. Ken Aquar

These are two different areas. I had problems with both over the past 4 years, and here is what I found to be the problems: The front bathroom has the depth transponder. The leak in this area usually

I also had a problem with the Bow Navigation Lights. I replaced the bulb several times, and then bit the bullet and replaced the wire and installed the 2NM Hella LED set. All mistakes. There is a link

Aquarius was fitted with new plugs on the Genoa Track, used 5200. Video https://www.youtube.com/watch?v=phe2_3JAji0 About 12:58 minutes is where it shows the new plugs. I am happy with them, they were

You asked for opinions..... With new solar, and lithium batteries the future of gensets has almost come to an end. You can put 2KW of solar on deck with 900AH of LiFePO4 batteries (at 24V). This would

I would have to agree with Bill, To fix you furler it will probably take a new motor, and maybe a new gearbox. I would rebuild the old gear box and carry it as a spare. I carry a new spare motor, and

1. Remove Rub Rail starting from Aft. 2. Remove all four lower bolts, then remove the upper single bolt holding the chainplate. 3. Clean hole and bolt with acetone. 4. Clean the Chainplate, Bolts, and

Well, I ended up using 5200. I bought some Sikaflex 295 (which is supposed to be like 4200) to do the job, as I could not find 4200 or Butyl Tape for sale anywhere in Krabi Thailand. But, after I pull

Hello, While in Fiji, SM007 and SM2K262 were parked next to each other. JP had a problem with his main, it was not unfurling completely. So I volunteered, and JP hoisted me up SM007's mast. What we fo

Hello James, After several Amelians suggested the use of Butyl Tape, and after a bit of research on the subject.... I am going to use the Butyl Tape. Though I am a bit worried about completely removin

Hi Bill, I knew the copper vent pipe for the fuel tank in the closet area, however, I didn't know about the potential condensation problem within the closet. I will look a bit closer at the potential

Thanks to all you Amelians for helping me through this mess! I think I have a good procedure for the repair now. But as aways, subject to change once I get into job. It looks as though it should take

Hi Erik, Here are some photos of the job at hand! I talked with some local boaties here at Krabi Boat Lagoon, and they suggested 5200. It has been raining for 5 days straight, and looks like it will c

Hello All, I pulled the rub rail up from aft to the chainplate, and now can see the nuts. Does anyone have a procedure how to reseal the chainplate bolt holes? Should I remove the entire chainplate, o

Hello Paul, Thanks for the response. Are there nuts under the rub rail, because the bolt heads are in the closet? Or, are the bolts threaded into the chainplate somehow? Other questions... There is al