Furling motor brushes


Kelly Ran
 

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston


david bruce
 

Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran <naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston


 

Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM <davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran <naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston


Danny and Yvonne SIMMS
 

Hi Dave,

If you need to reduce the size of carbon brushes it is easily and accurately achieved with a file.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 06:31 CW Bill Rouse <brouse@...> wrote:

Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM < davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran < naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric  SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston

 

 


Danny and Yvonne SIMMS
 

Hi again Dave, Just a little more on this. Put the file on a flat surface and rub the brush back and forth on it. Much more controllable that way.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 07:22 Danny and Yvonne SIMMS <simms@...> wrote:

Hi Dave,

If you need to reduce the size of carbon brushes it is easily and accurately achieved with a file.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 06:31 CW Bill Rouse <brouse@...> wrote:

Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM < davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran < naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric  SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston

 

 


 


 


Kelly Ran
 

Hi Bill,

I'm not quite sure what you mean -- the Eurton brushes are larger than the ones that Amel has in stock. The Eurton brushes fit very well in the keyway...it's a tight fit, and they still go in smoothly. I don't think jamming will be an issue, if that was your concern.

We will report back after a few months with how the brushes held up.

Best,
kelly + ryan
SM233 Iteration
Boston

On Wed, May 29, 2019 at 2:32 PM CW Bill Rouse <brouse@...> wrote:
Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM <davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran <naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston


 

I thought the brush was slightly smaller than the channel.

Best,

CW Bill Rouse
Yacht School - Supporting Amel Owners
www.YachtSchool.us
720 Winnie St
Galveston Island, TX 77550
+1(832) 380-4970

On Wed, May 29, 2019, 3:07 PM Kelly Ran <naryllek@...> wrote:
Hi Bill,

I'm not quite sure what you mean -- the Eurton brushes are larger than the ones that Amel has in stock. The Eurton brushes fit very well in the keyway...it's a tight fit, and they still go in smoothly. I don't think jamming will be an issue, if that was your concern.

We will report back after a few months with how the brushes held up.

Best,
kelly + ryan
SM233 Iteration
Boston

On Wed, May 29, 2019 at 2:32 PM CW Bill Rouse <brouse@...> wrote:
Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM <davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran <naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston


david bruce
 

Thanks Bill.

Best regards,  Dave. 
Liesse SN006 


On May 29, 2019, at 11:31 AM, CW Bill Rouse <brouse@...> wrote:

Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM <davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran <naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston


david bruce
 

Thanks Danny,   
Going to order a few of the Eurton brushes and plan to modify if or more accurately when they are needed.  
Appreciate the advice.  

Best, Dave
Liesse  SN 006 


On May 29, 2019, at 12:30 PM, Danny and Yvonne SIMMS <simms@...> wrote:

Hi again Dave, Just a little more on this. Put the file on a flat surface and rub the brush back and forth on it. Much more controllable that way.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 07:22 Danny and Yvonne SIMMS <simms@...> wrote:

Hi Dave,

If you need to reduce the size of carbon brushes it is easily and accurately achieved with a file.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 06:31 CW Bill Rouse <brouse@...> wrote:

Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM < davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran < naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric  SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston

 

 


 


 


 

Dave, 

That sounds like a really good plan.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Thu, May 30, 2019 at 1:01 PM <davidcbruce57@...> wrote:
Thanks Danny,   
Going to order a few of the Eurton brushes and plan to modify if or more accurately when they are needed.  
Appreciate the advice.  

Best, Dave
Liesse  SN 006 


On May 29, 2019, at 12:30 PM, Danny and Yvonne SIMMS <simms@...> wrote:

Hi again Dave, Just a little more on this. Put the file on a flat surface and rub the brush back and forth on it. Much more controllable that way.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 07:22 Danny and Yvonne SIMMS <simms@...> wrote:

Hi Dave,

If you need to reduce the size of carbon brushes it is easily and accurately achieved with a file.

Regards

Danny

SM 299

Ocean Pearl

On 30 May 2019 at 06:31 CW Bill Rouse <brouse@...> wrote:

Dave and Shelley,

There are at least 5-6 different Mainmast furling and outhaul motors tat have been used by Amel over the years. Additionally there are 12 volt (like yours) and 24 volt.

I suspect that even SAV at Amel cannot answer your question, except to say, "NO, the brushes are not the same."

I saw the slightly smaller brush used successfully by SM233 Iteration. Normally I would record the source of that brush as one to refer to my clients. I did not because I believe at some point that smaller width brush will cause a problem when it wears and the length becomes shorter. I may be wrong, and I am sure that only multiple experiences over time will prove me right or wrong.

One thing for sure is that you can always buy a larger electric motor brush and cut it to size. This is the safe solution. You may have to take the larger brush to a machine shop to have it cut.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Wed, May 29, 2019 at 1:20 PM < davidcbruce57@...> wrote:
Thanks for this sourcing information Kelly and Ryan.  

 Would anyone (Bill?) know if the brushes on all furling motors on a given boat as well as those on different model boats such as SM and SN are the same?    

Thanks, 

Dave and Shelley Bruce
Liesse, SN006 
Gaeta, Italy 

On May 28, 2019, at 3:48 PM, Kelly Ran < naryllek@...> wrote:

Hi all,

We recently needed to change the brushes on our main furling motor (Leroy Somer MBT86M).

I found an 8mm x 10mm x 17mm brush which works for us, so far. Unsure of the material but it looks similar to electrographite.

It seems that other owners have issues sourcing this brush, so here is the info:
Eurton Electric  SPR-A007  
7.50USD, ships from California

We also found that Maude has some slightly different brushes (8mm x 9mm x 16mm) in stock right now for 24 Euros. We did not order these, as the Eurton brushes work.

Fair winds,
kelly + ryan
SM233 Iteration
Boston

 

 


 


 


Mark McGovern
 
Edited

Thanks Kelly and Ryan for the information! These worked perfectly in our Leroy Somer MBT86M Main Furler and Outhaul motors.  Our main furler stopped working under any load at the end of last season.  It would spin freely when not loaded and I was able to easily furl and unfurl the mainsail manually so I figured it was likely worn brushes and/or a dirty armature.  Sure enough, it was both.  I replaced the brushes and cleaned the armature and they both work great.  Here is a direct link to the place I bought them:  https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

And here are some pictures of the brushes:

New brush on the left and old brush on right:




They really are a perfect fit and they are even cheaper when you buy 11 or more so I stocked up.  Thanks again for the information.  I love this group!

-
Mark McGovern
SM #440 Cara
Deale, MD USA


 

No doubt that Kelly and Ryan found something that will help many Amel owners.

Good call.

Best,

Bill Rouse
720 Winnie St.
Galveston, Texas 77550
832-380-4970



On Sun, Jun 9, 2019 at 1:41 PM Mark McGovern <mfmcgovern@...> wrote:
Thanks Kelly and Ryan for the information! These worked perfectly in our Leroy Somer MBT86M Main Furler and Outhaul motors.  Our main furler stopped working under any load at the end of last season.  It would spin freely when not loaded and I was able to easily furl and unfurl the mainsail manually so I figured it was likely worn brushes and/or a dirty armature.  Sure enough, it was both.  I replaced the brushes and cleaned the armature and they both work great.  Here is a direct link to the place I bought them:
https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

And here are some pictures of the brushes:

New brush on the left and old brush on right:




They really are a perfect fit and they are even cheaper when you buy 11 or more so I stocked up.  Thanks again for the information.  I love this group!

-
Mark McGovern
SM #440 Cara
Deale, MD USA


Donato Valente
 

Mark, 
Apparently the link you posted leads to a ‘page not found’. Would you please send it back ? Or detail the specs ? 

Thanks 

Donato 

SM 468 Ocean Bird





Il giorno dom 9 giu 2019 alle 20:41 Mark McGovern <mfmcgovern@...> ha scritto:
Thanks Kelly and Ryan for the information! These worked perfectly in our Leroy Somer MBT86M Main Furler and Outhaul motors.  Our main furler stopped working under any load at the end of last season.  It would spin freely when not loaded and I was able to easily furl and unfurl the mainsail manually so I figured it was likely worn brushes and/or a dirty armature.  Sure enough, it was both.  I replaced the brushes and cleaned the armature and they both work great.  Here is a direct link to the place I bought them:
https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

And here are some pictures of the brushes:

New brush on the left and old brush on right:




They really are a perfect fit and they are even cheaper when you buy 11 or more so I stocked up.  Thanks again for the information.  I love this group!

-
Mark McGovern
SM #440 Cara
Deale, MD USA


Kelly Ran
 

Mark, glad this worked for you! 😀

Donato, try this:

(Or try the hyperlink in my first message; that worked for me when I checked it)

Fair winds

Kelly + Ryan
SM233 Iteration


On Sun, Jun 9, 2019, 16:38 Donato Valente <ing.d.valente@...> wrote:
Mark, 
Apparently the link you posted leads to a ‘page not found’. Would you please send it back ? Or detail the specs ? 

Thanks 

Donato 

SM 468 Ocean Bird





Il giorno dom 9 giu 2019 alle 20:41 Mark McGovern <mfmcgovern@...> ha scritto:
Thanks Kelly and Ryan for the information! These worked perfectly in our Leroy Somer MBT86M Main Furler and Outhaul motors.  Our main furler stopped working under any load at the end of last season.  It would spin freely when not loaded and I was able to easily furl and unfurl the mainsail manually so I figured it was likely worn brushes and/or a dirty armature.  Sure enough, it was both.  I replaced the brushes and cleaned the armature and they both work great.  Here is a direct link to the place I bought them:
https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

And here are some pictures of the brushes:

New brush on the left and old brush on right:




They really are a perfect fit and they are even cheaper when you buy 11 or more so I stocked up.  Thanks again for the information.  I love this group!

-
Mark McGovern
SM #440 Cara
Deale, MD USA


Mark McGovern
 
Edited

Donato,

I think I fixed the link.  If not, use the link in Kelly and Ryans first post that says the part number SPR-A007.

--
Mark McGovern
SM #440 Cara
Deale, MD USA


Donato Valente
 

useful information.
Thanks Mark, thanks Kelly

fair winds 

Donato

SM #468 Ocean bird

Il giorno lun 10 giu 2019 alle ore 00:04 Mark McGovern <mfmcgovern@...> ha scritto:
Donate,

I think I fixed the link.  If not, use the link in Kelly and Ryans first post that says the part number SPR-A007.

--
Mark McGovern
SM #440 Cara
Deale, MD USA



--

___/)_____/)____/)_____

Ing. Donato Valente
mobile:+39 392 5390810
Skype ID: donato.valente


James Cromie
 

Mark - you used the A005 brush, and not the A007 from Eurton?  I believe someone else posted using the A007 for the Leroy Somer motor, but it looks like yours fit perfectly.  
Could you confirm that it is indeed the A005 that you used? 

By the way, the genoa toe pulleys look nice on my boat!  I’m about to try them out. 

Many Thanks.
James
SV Soteria SM2K 347  

On Jun 9, 2019, at 2:41 PM, Mark McGovern <mfmcgovern@...> wrote:

Thanks Kelly and Ryan for the information! These worked perfectly in our Leroy Somer MBT86M Main Furler and Outhaul motors.  Our main furler stopped working under any load at the end of last season.  It would spin freely when not loaded and I was able to easily furl and unfurl the mainsail manually so I figured it was likely worn brushes and/or a dirty armature.  Sure enough, it was both.  I replaced the brushes and cleaned the armature and they both work great.  Here is a direct link to the place I bought them:
https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

And here are some pictures of the brushes:

New brush on the left and old brush on right:
<IMG_20190609_130915759.jpg>


<IMG_20190609_130529854.jpg><IMG_20190609_130533911.jpg><IMG_20190609_130535656.jpg>
They really are a perfect fit and they are even cheaper when you buy 11 or more so I stocked up.  Thanks again for the information.  I love this group!

-
Mark McGovern
SM #440 Cara
Deale, MD USA


Kelly Ran
 

James-- the part number is SPR-A007.
The Eurton website has an incorrect URL, which is why I used a hyperlink in my initial email.
If you click on the link, you'll see that the page is for the 007 brush.

-kelly

On Thu, Jun 13, 2019 at 11:47 AM James Cromie via Groups.Io <jamescromie=yahoo.com@groups.io> wrote:
Mark - you used the A005 brush, and not the A007 from Eurton?  I believe someone else posted using the A007 for the Leroy Somer motor, but it looks like yours fit perfectly.  
Could you confirm that it is indeed the A005 that you used? 

By the way, the genoa toe pulleys look nice on my boat!  I’m about to try them out. 

Many Thanks.
James
SV Soteria SM2K 347  

On Jun 9, 2019, at 2:41 PM, Mark McGovern <mfmcgovern@...> wrote:

Thanks Kelly and Ryan for the information! These worked perfectly in our Leroy Somer MBT86M Main Furler and Outhaul motors.  Our main furler stopped working under any load at the end of last season.  It would spin freely when not loaded and I was able to easily furl and unfurl the mainsail manually so I figured it was likely worn brushes and/or a dirty armature.  Sure enough, it was both.  I replaced the brushes and cleaned the armature and they both work great.  Here is a direct link to the place I bought them:
https://store.eurtonelectric.com/31x31x6brushspr-a005-1-1-1.aspx

And here are some pictures of the brushes:

New brush on the left and old brush on right:
<IMG_20190609_130915759.jpg>


<IMG_20190609_130529854.jpg><IMG_20190609_130533911.jpg><IMG_20190609_130535656.jpg>
They really are a perfect fit and they are even cheaper when you buy 11 or more so I stocked up.  Thanks again for the information.  I love this group!

-
Mark McGovern
SM #440 Cara
Deale, MD USA


Mark McGovern
 

James,

The SPR-A007 brush fit perfectly in both my main furler motor and outhaul motor.  The link on the Eurton website says "A005" in the hyperlink for some reason but the correct part number is SPR-A007. 
 
--
Mark McGovern
SM #440 Cara
Deale, MD USA


James Cromie
 

Thanks Mark and Kelly for confirming.  

-James

On Jun 13, 2019, at 12:13 PM, Mark McGovern <mfmcgovern@...> wrote:

James,

The SPR-A007 brush fit perfectly in both my main furler motor and outhaul motor.  The link on the Eurton website says "A005" in the hyperlink for some reason but the correct part number is SPR-A007. 
 
--
Mark McGovern
SM #440 Cara
Deale, MD USA