Brush set (4) for jib furler motor Supermaramu


 

This is everything you may need including brush sizes and where to get them



CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Thu, Jul 28, 2022 at 4:43 PM ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Thanks Marian and Bill for good info re jib furling motor brushes. When back on the boat in August, will take more pics and continue research.  Again, thanks all,  Eric

On Thu, Jul 28, 2022 at 9:27 AM Marian Toncic-Sorinj <marian@...> wrote:
I have a 12v System.
Furlermotor (Same as yours on your Picture) and Lofrans Tigres motor are the same. You need the 24v Motor i think. Both are available.
My Contact to Lofrans was
+39 039 2001973. you should talk to them because of the brushkits

Here are Pictures of my FurlerMotor ,

imageimage

Marian

Am 28.07.2022 um 15:31 schrieb CW Bill Rouse <brouse@...>:


Eric,

Lofrans uses many different motors. Do you know which is the same as the genoa motor?
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Thu, Jul 28, 2022 at 6:09 AM Marian Toncic-Sorinj <marian@...> wrote:

Am 2022-07-27 02:47, schrieb ERIC LICHTY & ROBYN ATKINSON:

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric
 
--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720

Hello Eric,

i had similar Problems. These are old Bosch-Motors that are not supported any more. But Lofrans produces these motors now. for example "Lofrans-Tigres Anchorwinslet" is driven by exact this Motor. Best regards Marian



--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


ERIC LICHTY & ROBYN ATKINSON
 

Thanks Marian and Bill for good info re jib furling motor brushes. When back on the boat in August, will take more pics and continue research.  Again, thanks all,  Eric


On Thu, Jul 28, 2022 at 9:27 AM Marian Toncic-Sorinj <marian@...> wrote:
I have a 12v System.
Furlermotor (Same as yours on your Picture) and Lofrans Tigres motor are the same. You need the 24v Motor i think. Both are available.
My Contact to Lofrans was
+39 039 2001973. you should talk to them because of the brushkits

Here are Pictures of my FurlerMotor ,

imageimage

Marian

Am 28.07.2022 um 15:31 schrieb CW Bill Rouse <brouse@...>:


Eric,

Lofrans uses many different motors. Do you know which is the same as the genoa motor?
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Thu, Jul 28, 2022 at 6:09 AM Marian Toncic-Sorinj <marian@...> wrote:

Am 2022-07-27 02:47, schrieb ERIC LICHTY & ROBYN ATKINSON:

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric
 
--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720

Hello Eric,

i had similar Problems. These are old Bosch-Motors that are not supported any more. But Lofrans produces these motors now. for example "Lofrans-Tigres Anchorwinslet" is driven by exact this Motor. Best regards Marian



--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


Marian Toncic-Sorinj
 

I have a 12v System.
Furlermotor (Same as yours on your Picture) and Lofrans Tigres motor are the same. You need the 24v Motor i think. Both are available.
My Contact to Lofrans was
+39 039 2001973. you should talk to them because of the brushkits

Here are Pictures of my FurlerMotor ,

imageimage

Marian

Am 28.07.2022 um 15:31 schrieb CW Bill Rouse <brouse@...>:


Eric,

Lofrans uses many different motors. Do you know which is the same as the genoa motor?
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Thu, Jul 28, 2022 at 6:09 AM Marian Toncic-Sorinj <marian@...> wrote:

Am 2022-07-27 02:47, schrieb ERIC LICHTY & ROBYN ATKINSON:

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric
 
--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720

Hello Eric,

i had similar Problems. These are old Bosch-Motors that are not supported any more. But Lofrans produces these motors now. for example "Lofrans-Tigres Anchorwinslet" is driven by exact this Motor. Best regards Marian


 

Eric,

Lofrans uses many different motors. Do you know which is the same as the genoa motor?
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Thu, Jul 28, 2022 at 6:09 AM Marian Toncic-Sorinj <marian@...> wrote:

Am 2022-07-27 02:47, schrieb ERIC LICHTY & ROBYN ATKINSON:

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric
 
--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720

Hello Eric,

i had similar Problems. These are old Bosch-Motors that are not supported any more. But Lofrans produces these motors now. for example "Lofrans-Tigres Anchorwinslet" is driven by exact this Motor. Best regards Marian


Marian Toncic-Sorinj
 

Am 2022-07-27 02:47, schrieb ERIC LICHTY & ROBYN ATKINSON:

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric
 
--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720

Hello Eric,

i had similar Problems. These are old Bosch-Motors that are not supported any more. But Lofrans produces these motors now. for example "Lofrans-Tigres Anchorwinslet" is driven by exact this Motor. Best regards Marian


ERIC LICHTY & ROBYN ATKINSON
 

Thank you for brush replies........working on it.  (Furler working fine)


On Wed, Jul 27, 2022 at 12:19 PM CW Bill Rouse <brouse@...> wrote:
Eric,

OK, I have sent an email to the person I believe has inventory of this motor in Europe.

As soon as I receive an answer, I will get back to you.

Bill


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Wed, Jul 27, 2022 at 2:09 PM ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Thanks for your time, away from boat so no pics other than the one in original email.

On Wed, Jul 27, 2022, 6:15 AM CW Bill Rouse <brouse@...> wrote:
Eric,

Which Anel Genoa furler do you have?

1.) Early Model:
image.png

2.) Late Model:
image.png



Late Model 24v motor:
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Tue, Jul 26, 2022 at 10:32 PM Bill Rouse <brouse@...> wrote:
I have a source for a new motor if the Genoa furler is the version I think it is and not the earlier version. I can tell if you post a photo, and BTW, if any owner responds with spares, you will also need to determine the version. I will get back to you in a day or 2

Please post a photo. 

Best,

CW Bill Rouse 
Amel Owners Yacht School
+1 832-380-4970 | brouse@...
720 Winnie, Galveston Island, Texas 77550 
www.AmelOwnersYachtSchool.com 
Yacht School Calendar: www.preparetocastoff.blogspot.com/p/calendar.html


   

On Tue, Jul 26, 2022, 19:48 ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720



--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


 

Eric,

OK, I have sent an email to the person I believe has inventory of this motor in Europe.

As soon as I receive an answer, I will get back to you.

Bill


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Wed, Jul 27, 2022 at 2:09 PM ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Thanks for your time, away from boat so no pics other than the one in original email.

On Wed, Jul 27, 2022, 6:15 AM CW Bill Rouse <brouse@...> wrote:
Eric,

Which Anel Genoa furler do you have?

1.) Early Model:
image.png

2.) Late Model:
image.png



Late Model 24v motor:
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Tue, Jul 26, 2022 at 10:32 PM Bill Rouse <brouse@...> wrote:
I have a source for a new motor if the Genoa furler is the version I think it is and not the earlier version. I can tell if you post a photo, and BTW, if any owner responds with spares, you will also need to determine the version. I will get back to you in a day or 2

Please post a photo. 

Best,

CW Bill Rouse 
Amel Owners Yacht School
+1 832-380-4970 | brouse@...
720 Winnie, Galveston Island, Texas 77550 
www.AmelOwnersYachtSchool.com 
Yacht School Calendar: www.preparetocastoff.blogspot.com/p/calendar.html


   

On Tue, Jul 26, 2022, 19:48 ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


ERIC LICHTY & ROBYN ATKINSON
 

Thanks for your time, away from boat so no pics other than the one in original email.


On Wed, Jul 27, 2022, 6:15 AM CW Bill Rouse <brouse@...> wrote:
Eric,

Which Anel Genoa furler do you have?

1.) Early Model:
image.png

2.) Late Model:
image.png



Late Model 24v motor:
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Tue, Jul 26, 2022 at 10:32 PM Bill Rouse <brouse@...> wrote:
I have a source for a new motor if the Genoa furler is the version I think it is and not the earlier version. I can tell if you post a photo, and BTW, if any owner responds with spares, you will also need to determine the version. I will get back to you in a day or 2

Please post a photo. 

Best,

CW Bill Rouse 
Amel Owners Yacht School
+1 832-380-4970 | brouse@...
720 Winnie, Galveston Island, Texas 77550 
www.AmelOwnersYachtSchool.com 
Yacht School Calendar: www.preparetocastoff.blogspot.com/p/calendar.html


   

On Tue, Jul 26, 2022, 19:48 ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


ERIC LICHTY & ROBYN ATKINSON
 

Late model


On Wed, Jul 27, 2022, 6:15 AM CW Bill Rouse <brouse@...> wrote:
Eric,

Which Anel Genoa furler do you have?

1.) Early Model:
image.png

2.) Late Model:
image.png



Late Model 24v motor:
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   

On Tue, Jul 26, 2022 at 10:32 PM Bill Rouse <brouse@...> wrote:
I have a source for a new motor if the Genoa furler is the version I think it is and not the earlier version. I can tell if you post a photo, and BTW, if any owner responds with spares, you will also need to determine the version. I will get back to you in a day or 2

Please post a photo. 

Best,

CW Bill Rouse 
Amel Owners Yacht School
+1 832-380-4970 | brouse@...
720 Winnie, Galveston Island, Texas 77550 
www.AmelOwnersYachtSchool.com 
Yacht School Calendar: www.preparetocastoff.blogspot.com/p/calendar.html


   

On Tue, Jul 26, 2022, 19:48 ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


Bill Kinney
 

Eric,

I have seen two different styles of motor installed in the genoa furler, one in our (1996) original, and one from the end of the production run, and both are different than your photo!  The early motor was a Bosch, and the later one was out of Iran.

I can’t help you with a specific brush recommendation, but you might try here:  https://www.graphitestore.com/Carbon-Brushes/Brushes

They have a huge variety of different brushes, and might be able to match what you have.

Bill Kinney
SM160, Harmonie
Port Louis, Grenada.


 

Eric,

Which Anel Genoa furler do you have?

1.) Early Model:
image.png

2.) Late Model:
image.png



Late Model 24v motor:
image.png


CW Bill Rouse Amel Owners Yacht School
720 Winnie, Galveston Island, Texas 77550 
   


On Tue, Jul 26, 2022 at 10:32 PM Bill Rouse <brouse@...> wrote:
I have a source for a new motor if the Genoa furler is the version I think it is and not the earlier version. I can tell if you post a photo, and BTW, if any owner responds with spares, you will also need to determine the version. I will get back to you in a day or 2

Please post a photo. 

Best,

CW Bill Rouse 
Amel Owners Yacht School
+1 832-380-4970 | brouse@...
720 Winnie, Galveston Island, Texas 77550 
www.AmelOwnersYachtSchool.com 
Yacht School Calendar: www.preparetocastoff.blogspot.com/p/calendar.html


   

On Tue, Jul 26, 2022, 19:48 ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


 

I have a source for a new motor if the Genoa furler is the version I think it is and not the earlier version. I can tell if you post a photo, and BTW, if any owner responds with spares, you will also need to determine the version. I will get back to you in a day or 2

Please post a photo. 

Best,

CW Bill Rouse 
Amel Owners Yacht School
+1 832-380-4970 | brouse@...
720 Winnie, Galveston Island, Texas 77550 
www.AmelOwnersYachtSchool.com 
Yacht School Calendar: www.preparetocastoff.blogspot.com/p/calendar.html


   


On Tue, Jul 26, 2022, 19:48 ERIC LICHTY & ROBYN ATKINSON <eclmarine@...> wrote:
Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720


ERIC LICHTY & ROBYN ATKINSON
 

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles

Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush sets. Confirmed power to motor and foil turning easily.  Cleaned/vaccumed salt deposits then electrical cleaner and corrosionx.
Motor runs quiet and strong, back in business.  Now looking for source for brush set (4) for the 24v motor.  Any spec. plate is long gone and inquiries to SAV@Amel indicate the motor and parts are no longer supported.  Does anyone happen to have a source for those brushes or anyone with extra spares willing to sell four?   Regards and good sailing, Eric

--
Eric C. Lichty
ECLMARINE, LLC.
cell:      425 354-7720