I am currently replacing the damaged gears of the bow thruster (broken bearing), using the original Amel kit (incidentally, out of stock at my normal suppliers, Amel Hyères– had to apply directly to l

There is an Amel owner that should arrive in Gilbraltar in a few days ,his Onan is dead and asked me to see if I could find an Onan mechanic there before he arrives. If anyone knows of one and has con

Hi, Our shaft generator was working fine, but after a total breakdown of our 24v supply (24v alternator defective and Onan generator not starting), it doesn’t load anymore. Before the 24v breakdown, b

Gentlemen, My Amel 55 has a leaking forward deck hatch, it seems to be the southco latch, Does anyone know where to buy seals for these latches? Couldn’t find any parts on the southco website. Bob Gre

All concerned. I learned a few things this morning while discussing the Mainmast Furling motor with Mohammad Shirloo, A54 #099 B&B Kokomo, Here they are: The vertical mainmast furling motor from Amel

Hi Group, Hope all are having great covid restrictions free summer. My new problem is that folding order (to main furler) does not reach the Solenoid (as I don’t hear the ‘Clack’), opening is ok, swit

Hi, A54 owners, can you share please the Amel intended way how to rig backstay, stay sail, and genaker blocks? from the user manual I found that backstay runners should be blocked to the main back sta

Good ZOOM hook-up - thank you Bill & Tilo for organising and moderating. I learnt a few good things: use of high-resolution models for local forecasts; and the better speed of the PWoffshore APP becau

Does anyone have a source (preferably USA) for the rubber caps for the windless buttons? The buttons are fine, but the caps need replacement. Thanks With best regards, Mark Skipper Sailing Vessel - Cr

This morning I changed the Desalateur end caps.(160l) The only thing I want to add to the common knowledge is that I found that the air blower needed to be dropped in order to access the forward outbo

Reminder: PredictWind Presentation by Keyrn McMaster, Ocean Racer and Executive with PredictWind When: 06/18/2022 20:00 to 21:00 (UTC+00:00) UTC Where: Group Zoom Meeting Organizer: Bill Rouse brouse@

Reminder: PredictWind Presentation by Keyrn McMaster, Ocean Racer and Executive with PredictWind When: 06/18/2022 20:00 to 21:00 (UTC+00:00) UTC Where: Group Zoom Meeting Organizer: Bill Rouse brouse@

Please see https://amelyachtowners.groups.io/g/SharkiMaramuMango/topic/advise_for_broken_propeller/91839282?p=,,,20,0,0,0::recentpostdate/sticky,,,20,2,0,91839282,previd%3D1655554862542162790,nextid%3

Hello, When rolling slightly on anchor or in light winds, the cables in the mizzen are banging inside. It is rather annoying and I imagine it will damage the cables. I think there should be some foam

PredictWind Presentation by Keyrn McMaster, Ocean Racer and Executive with PredictWind When: Saturday, June 18, 2022 20:00 to 21:00 (UTC+00:00) UTC Where: Group Zoom Meeting Organizer: Bill Rouse brou

Has anyone found a hard-wired instrument to replace the Omega EC controller model CDCN-201? Mine died. Fair Winds Eric Kimberlite Amel Super Maramu #376

Afternoon, looking for some wisdom/advice…. I just completed my first bow thruster maint. While reassembling bow thruster with new lip seals I ran into an issue with the small seal that goes over the

Dear all, A few days ago I dismantled my original SM fresh water pump to clean off lots of rust on a body of electric motor. Did that, gave it a lick of paint, installed it back and it is no longer wo

Last year I had new plastic windows on my spray hood as the old had gone opaque. I have spayed the whole thing with waterproofing agent but the stitch holes around the new windows drip a bit in rain.

PredictWind Presentation by Keyrn McMaster, Ocean Racer and Executive with PredictWind When: Saturday, June 18, 2022 20:00 to 21:00 (UTC+00:00) UTC Where: Group Zoom Meeting Organizer: Bill Rouse brou