Hi again Peter. James points out some important things to consider regarding how the oil pressure gets displayed and/or sets off warning alarms. In my experience, most commonly a fault in the measurin

Hello, I am wondering if anyone is currently hauled out ? I would like to check a below the waterline measurement. thank you Paul Guenette ARAMIS SM 2000 - 444 Port Townsend, Washington

David, I think that was added by a PO and is probably an outlet for a chain wash. Bill CW Bill Rouse Amel Owners Yacht School +1 832-380-4970 | brouse@... 720 Winnie, Galveston Island, Texas 77550 www

Santorin & Super Maramu owners. Amel SM Genoa Repair and Replacement Parts: The Second generation of the Amel Electric Genoa Furlers used on various Amel Santorins and Super Maramus were manufactured

Hello Amelians iI réalise that the drivers of my Raymarine autopilot ACU400,Evolution EV1 & controller P70 Are all in need of updating . is there a way to do it with a computer ( Mac !) or one has to

I just bought Kanuméra a 1980 Sharki based in Nouméa, New Caledonia. I want to renovate the deck, cockpit, foredeck, and hull. Can someone give me the RAL numbers ? On the forum, I found hull RAL 9010

Hi, since my old bats will die soon I decided to go LiFePo. It will most likely done out of on hand, meaning the Victron main Importer in Turkey. please advise and let me know the little things to loo

After installing the 5 KW inverter we decided to make a well-vented enclosure for the wet closet. I wanted to make sure that the handle next to the navigation table was preserved. Here is the result a

I just got delivered Aqua Signal 34 LED Tricolor plus anchor navigation light. Regarding voltage it is written 12/24V. I can not find the max voltage for this lamp. Should I convert 24V to 12V to be o

Dear fellow Amelians, Does anyone know power characteristics (kW or Amps) of Super Maramu 2000’s (2004 onwards) bowthruster and whether it has any fuse or disruptor, apart from the one on the 24V boar

Hello, I have been on the site for a few years and have interest in eventually purchasing an Amel for cruising in retirement. My wife and I would like to see if there are any Amels that could be visit

Hello Group: Eric and Robyn here on LIBBY, SM#196, 1997 build, sailing out of Los Angeles Jib furler motor stopped working. Removed cover and found a handful of salt residue up to and in the brush set

Hello, I just ordered a Starlink RV and try to figure out where to mount the antenna. I would prefer to mount it fix under deck. The only place I found till now is above the chart table in the middle

I was recently watching a random YouTube where the boat owner was replacing his storage hot water system with an on demand electric heater. I dont like changing Henry's well thought out systems though

The generator was running fine, was a way from the boat for a month and tried to fire up my Northern Lights generator, on the control panel no green light, and the I press the start button the Sea Fir

Hi all, We want to replace the upper shrouds, middle shrouds and lower shrouds of the main mast . Is there a recommended rigger on the French or Spanish Mediterranean coast? All the necessary material

Good Morning, I just received news that the motor in both my barely used BAMAR EFJ furlers are shot (=dead) ☹ Since I am now looking for at least the 3rd (that I know off) but possibly 4th set of elec

Time to replace the portlight and hatch seals on Minerva, Maramu #135. I looked in the wiki-how on this site, but the attachment with Bill Rouse’s response to a similar question was deleted. Does anyo

Hello, I wonder if anyone can help me identify this little thing I found on deck yesterday? I located it on the starboard side at the rail close to the aft cabin but it could have come from anywhere.

Good morning! I have discovered one of my floorboard hatches is broken and needs replacing. I emailed Maude a couple days ago and am awaiting a reply. In the meantime I thought I’d check with the grou