Dear Bill thanks a lot for your valuable information. I will go thought with the mechanic it and I let you know. Do you have a schemE of the SM GROUND LINE, I MEAN the cable that connect all the metal

Hello Amelians! I am in the process of learning my boat. The engine is a Volvo TMD22, with autoprop h6 propeller. I found some threads here on the forum related to this topic, but none conclusive abou

Here is a photo of some of the plumbing under the sink of the SM. Fair winds, Eric sm376

Hello dear Amelians, Finaly on board again of my SM in Greece, I want to start sailing today, but there appeared a small problem. The inlet valve of the washing machine will not close for 100%. So I l

I previously had a source for the exact replacement of the igniter for Eno stoves needing 6 outlets (4 burners + 2 oven burners). If you are adventurous and want to try something with little risk, let

My B&G Vulcan 7FS failed at the helm and i purchased a new Vulcan 7R. Because its a boat, its mounting system is slightly different so I need to enlarge the hole and drill new holes. I'm thinking of u

I have about 4 layers of paint on my boat I would like to be rid of. I have been sanding boats for over 50 yrs. and have never found it fun. Using 40 grit on a 5 " orbital today,it took so long to get

I'm about to replace the exhaust hose for the main engine from the waterlift muffler to the hull fitting. Seems a simple task, but I'd appreciate any tips from those who have already been there. I rea

Hi y'all, Has anyone found a source in the UK for the oil seal 29x 42x 8 ? I have been offered 29x41x8 and 28x42x6. I guess this last one would do but I would prefer to get the right one, just in case

Dear amelians Today's topic concerns the Amel 55 model At marina berth , when the wind enters from the stern at 130-150º angles and with 10-15 knots of wind, there is an enormous vibration in the mize

Hi, I had a very little water near the rudder shaft after some heavy seas. Wanted to tighten the nut, bit its too big for my tools. Any advice or do I need another special tool? Tbanks -- Bernd SN 119

Hi All, I'm replacing the Gianneshi fresh water pump. Can anyone tell me the recommended high and low water pressure values please? I have the original Gianneschi ACB-61-G pressure tank and pump syste

Hello Group Tom Deasy APHRODITE Maramu 1983 #125 I am having a problem with my electric furler, four years old and several thousand miles.It will unroll about 2 feet and stop it will not roll back up.

Here are a few photos of the finished jobOn July 7, 2020 at 12:47 PM eric freedman <kimberlite@...> wrote: Hi Tom Here are some photos of the rewiring. In the 4th photo is a black wire that Amel used

Hi Tom Here are some photos of the rewiring. In the 4th photo is a black wire that Amel used to connect all the negative sides of the senders. There were numerous connections and a few bad solder join

https://amelyachtowners.groups.io/g/main/files/Miscellaneous/_Kit%20isolation%20Yanmar.pdf Tom, I believe this is what you have. This is the newer conversion. I see the relay you are referring to. The

Canceled - ZOOM Meeting - Canceled, Presentation from the owner of QSails When: Saturday, 11 July 2020 20:00 to 21:00 (UTC+00:00) UTC Description: The owner and manager of QSails will be unable to att

Or, you can accomplish the same result using a couple of swimming noodles with a line through them and tied under the stern of the boat. With best regards, Mark Skipper Sailing Vessel - Cream Puff - S

Hello, I just become the owner of SM 2000 hull nr. 279. Name Bonne Anse. Boat speed is not working. Surveyer Oliver said that problem is in sensor. Any experince if I would change with sensor for dept

Reminder: ZOOM Meeting, Presentation from the owner of QSails on sailcloth and sail construction When: Saturday, 11 July 2020, 20:00 to 21:00, (GMT+00:00) UTC An RSVP is requested. Click here to RSVP