Dear Amelians, when Olivier did the survey of Borador he noticed the "Main sheet tackle broken catch" was broken. It seems to be a very difficult part to get and Amel does not have it. Can anyone help

Greetings, The switch housing for the Climma Air Conditioning Controls finally broke completely. I have looked online and have not found a reliable source for a replacement. I contacted SAV but they h

Hallo to the group, recently I found to pieces of POM but I have no idea what they are made for. Any idea? Thanks Martin Birkhoff Mago del Sur - 54#40

Hallo to the group, the relais fitted to our bowthruster is not original for sure and a cause of constant problems. It is an Albright relais but there are no specifications given on the housing. From

Hello again. In my search for the right vessel made by Henri Amel, I am looking for a list of the boats of his creation post 1990. If someone has a convent link or list, that would fantastic. Thanks,

It's the end of an era. At least the Amel Group is still around. Hopefully we can gather all documentation before the end of support. Aras Sharki #163 1988 ---------- Forwarded message --------- From:

Moldy pywood can be saved. Just clean it, dry well and apply penetrating epoxy. Follow instructions. Your can add a layer of fiberglass on top if needed. Vladimir SM 345 "LIFE IS GOOD"

A question to those who needed to replace the VHF cable in the main mast: Did you also need to replace the VHF cable from the base of the mast to the rear of the radio? Thanks. With best regards, Mark

The following files have been uploaded to the Files area of the main@AmelYachtOwners.groups.io group. /Amel Reviews/Super maramu test revu bateau 1789.pdf /Amel Reviews/Super maramu test revu yachting

The following files have been uploaded to the Files area of the main@AmelYachtOwners.groups.io group. /Amel Brochures/BROCHURE AMEL 54-FR.pdf /Amel Brochures/BROCHURE AMEL 54-GB.pdf /Amel Brochures/BR

Hello all. I am looking for a source for 54mm stern tube hose for my stuffing box on my 1985 mango. 54 mm is equal to 2 1/8 inches. Preferably a U.S. supplier as we are located in the US and need it n

Would anyone know the transmission ration for a Perkins Prima M50 engine with a Hurth transmission gear ratio? My prop measure 19". I'm replacing my engine with a Beta Marine 50 and TCM 60 Tranny (2:1

Hi All, Upgrading my old Autohelm 6000 for a Raymarine Evolution Autopilot on my Santorin. The existing fluxgate compass from the Autohelm sits behind the port-side sofa backrest in the salon - within

Hello all. I have also dismantled the gearbox of the main's furler because it made a horrible sound and finally didn't have enough strength to move the furler. Now I have the gearbox over my table, an

My forward inspection port (the one with the fuel level gauge) is leaking. I decided to change both gaskets but "practice" with the rear most port as it's easier. I was surprised to find that it isn't

Hello: I have just noticed two green wires close to the rudder post in Flora, and I have attached a photo. These two wires have been disconnected and I dont know why or by whom. Does anyone know what

This is a rough outline of a self insurance or shared risk co-op, that I sent Kent and thought I would share with the group. It was prompted by the hassle I have had with obtaining insurance, the rest

So for the last several days we had some quite strong Northeasters blowing [gusting up to 30 knots]. These unrelenting winds have taken a toll on my 30 year old chock. I need to replace them. I sent M

Hi All, Can anyone tell me where i could find a supplier of electromax alternators in Europe. Regards Steve s/v Dusk

Hi Amelians, after 40 years, the hand basin on my Sharki is no longer attractive - says my wife. Does anyone know the manufacturer or dealer who still sells such sinks? Best Regards Ralf SV Baghira, S