Good morning, I contacted Maude looking for a replacement deck cap fitting for my head pump out tank but was informed Amel does not carry that part anymore. Has anyone sourced this part elsewhere? Kev

One of the bolts on my main switch broke off. Anyone know if they still exist or do I need to replace it with another model? Paul on sykerpa SM 259 Lagos Portugal

Good morning all, On sv BeBe, SM#387, I have the original Dessalator 230v 160LPH water-maker. Today was the first time I this season that I have tried to run the water maker (as we were in the muddy C

In need of a Lewmar Medium Profile Hatch gasket size 50 - found a deal that may include free freight and a 10% discount. Hurry before they are gone! -- Mark Mueller Brass Ring A54

I have spent the last couple of days trying to debug the side-power bow thruster on my boat, and the up/down 4 relay system. My motor for up/down had a bad bearing and was blowing a fuse. It appears t

Hello Dan; We have the same water maker aboard Kokomo. However, I’m not sure if it is the same or a later design. Going through your procedure, I have one recommendation. I see that you state that you

Hi does anyone have the dimensions of the board you use to secure the hatch on a 54? Mine has become warped and I need to make a new one but am not on the boat. Cheers Courtney 54 #101 Trippin Brunswi

Would anyone be able to recommend a surveyor in the Charleston area please? Ideally one with Amel experience. thanks

He all ever thought about switching the 12-V altinator to charge the launch battery for a 24-ounce and using the service batteries to speed up the charges. If we're charging the launch battery, we'd h

Hello is there a list of all disruptors installed on Amel 54 (by ref and spec)? I understand there are different references (either unipolar / bipolar). Need to source a replacement for 7122104 10D (7

Hi to all, after 12 years sailing around the world, I planned to improve the aesthetical aspect of “Eutikia” deck as the Faux Caulking (black lines) had suffered from UV, salt and very hot temperature

Hi.I have encountered this problem with my main furler motor. I have sheared the shaft on the leroy somer motor where it enters the gearbox. Any suggestions on how I would be causing this problem? The

Dear All, When I was child growing up I was told that I could find a Pot of Gold at the end of a Rainbow. Voila, I found it. An “AMEL”. Next to us in our anchorage. Very Best Barry and Penny “SV Lady

Hello All, I had posted availability of 4 pr of the silicone seals that I had available from my order of 10 (min order size). Since they have been spoken for and I have had some additional interest, I

Hi, we would like to source some new plugs for the galley sink. These are for a sm2000 with the original sink. I have searched the website and not found any information. I did hear a mention awhile ag

Fellow Amelians, I am not sure who the current owners of Bali Hai are, but on Nov. 2 they abandoned her off Cape Hatteras as they were rescued by the US Coast Guard after their engine apparently faile

I have very bad hutch door on my SM. Does not look nice at all. See photo attached. I am not sure how to get it better. Just sand it, put some epoxy and then several layers of UV protected varnish. Is

Two nights ago our shore power breaker tripped, so I shut all power circuits down on the boat and tried to reset it and got a spark and smoke at the shore power pedestal. Tried another pedestal so beg

Dear all! we bought our OYA, a SM 2000, 373 in April. now we want to change the alternator to a bigger 175 amp. The engine is still the original Yanmar 75hp from 2002. Is there anyone with good experi

Hi- maybe someone can help me understand... The Super Maramu 2k Manual shows that the bow thruster draws 7000W and 510A at 24V. Is this correct? If so, how does the math work out? W=VxA is violated AN