We have the Idromini Acb Waterpump from Gianneschi. Sometimes it will not stop, the pump continues. We have to stop it manually on the pressure switch.... I have pumped up to 2 bar and cleaned the pre

Sharing some info' for the benefit of those folks who are wanting to fix the back lights that illuminate the breaker panel labels. Almost none of the LED’s back lighting the breaker panel labels on my

On SM2K 422 there is a outlet fitting and hose at the top aft of the fuel tank. It runs down the scupper to a "T" next to the genset muffler. One leg runs back under the Yanmar and I can't see where i

Hi all, Unfortunately we just got a damage On the hull due to failing equipment in a marina. The marina will cover the cost for repairing it, but we need the color code of the gelgote. Can any of you

Good day fellow sailors. I didn’t pay too much attention to this topic when I read it as I didn’t think we had the problem. However, a week or so ago, when Chuck and Kim on S/V Joy stopped by, Chuck h

Hello Our SSB Antenna comes in 2 parts. The threading that connects them has gotten loose and we would like to find away to secure them that doesn’t impact the transmission. Has anyone had this issue?

Hi All, I have just bought new Antal Traveler Blocks for my Super Maramu. The reason I bought new ones is that a few older boats have experienced a few breakages and hopefully I will get to do a few m

I can’t find any breaker for the bow thruster and genoa furler motor. There is a 100amp fuse located in the bow thruster recess near the solenoids. also when I turned off the main 12v power for the bo

Thank you all for the excellent advice. I have found and solved the problem... It was the Bowthruster after all. A build up of carbon dust from the brushes on top of the commutator bridged up to the t

Hello All, We are attending Cruisers University and possibly the Sailboat Show in Annapolis, MD early October. Was wondering if others were planning to attend, and might there be an opportunity to get

I contacted Maud about buying a new rub rail insert ,she cannot provide an estimate for shipping. We are thinking it may be much more than we first estimated. Has anyone had the inserts shipped to the

Hello, does anybody have a table of running rig for the Super Maramu 2000, with all lenght and diameters. That would be a great Help for me best rerards Roman

Hi all, Does anyone know the precise length of cable required to go from the top of the main mast to the chart table through the standard conduit on the Amel 54? For instance for the VHF antenna cable

An owner just made an inquiry about the rub rail purchase, by going back to a post back in Feb. under subject titled “Rub rail insert ,“which brought it to the forefront . Please ,if interested in the

Hello, last time when connected to shore power I have used dishwasher and after one minute all the power went off. Including the shore power unit. This did not happened when running air conditioning o

Back sailing and all well aboard Amelia here in the windy Cyclades. Since launching a few days ago I have found that the “ Masse” leak to the bonding system lights up on the negative side. So far I ha

OK- I have hull #422 (a red line) and each day I wistfully look at that un-used dive compressor breaker on the 220 volt panel and feel like it's talking to me. My wife and I are enthusiastic divers he

Can anyone advise why there are two 500A Mastershunts installed at the outset. We see that only one Mastershunt is configured and visible on the monitor. The second does not appear to be visible

I want to clean my fuel tank, I can only see one small cap that I assume is for the sending unit. Before I tear off the foam cover glued to the tank looking for a larger inspection port, I thought I w

My SM Pure Magic, hull no. 433, is presently connected to shorepower @ 220V, 60 Hz. During a recent inspection I was asked to operate the Onan genset, but overlooked switching off the small battery ch