Helllo Richard, Our Unold induction cook plate has suction cups and is very secure on our Corian counter top during very heavy weather. Otherwise, it resides on top of the gas burners and stays well i

On the inboard side of the companionway there are two threaded bolts sticking out of it. Sitting on each bolt is a piece of stiff plastic tubing inside of a coil spring in the first photo attached . T

My 28 year old max prop developed a crack in the body, discovered on a recent haulout. Never caused issues (when I owned it), but It is not repairable, so they say. Any suggestions or experiences out

Amalians, Could anyone send me some photos of the cockpit closure mechanism? When you pull up the door with the bar I thought to remember that it falls into the slot without having to turn the black p

Does anyone have a good wiring schematic for the original Pochon Chain counter. I have the factory drawings which are not decipherable even if you read French. I have 3 cables coming to the panel inst

I noticed a couple of years ago while I was in my forward port locker ,I could see daylight coming thru the chainplate, I had forgotten about it until a couple of weeks ago when I was in it again. Sin

Hi Eric I’m back on board , so there are pictures of my mécanism that works a treat -- Nicolas Klene DarNico SM2K # 471 In Marseille

My tie rods attaching the ram to the transom are pretty corroded. You can see the old one (Durbal BEF 12-60-501 Aluminium) and the replacement I got from Amel (Fluro GIRSW 12 RR 316) which is stainles

This is specifically for Amel SM owners with the Yanmar 4JH3-HTE engine who have replaced the Exhaust Elbow with the cast SS replacement. (see attached photos) I am planning to replace the ~1 meter ex

Our chain counter resets to 78.2 meters whenever it is powered off and on. We reset to zero, when the anchor is up and everything works fine, The issue obviously, is when we go to bring up the anchor,

Ok so here it is. I have been thinking about getting an Amel for quite a while and am about ready to make the leap, but with all things I over think everything. I love the boat, but the inmast furling

Hello al Amel friends! i have just payd the first 10% for a SM2K 2005. Son named S/Y TINTIN The gearbox for the jib is broken. the owner is willing to reduce the price for a repare and leave me to sol

> > Dear all, > > We just received our brand new drive unit from Amel and are wondering if anyone else has replaced theirs and has any advice for us. We have a mechanical engineer to do the job but i

We are contemplating osmosis treatment for our Mango. Unfortunately our boat seems to be a victim of the 'bad' resin catalyst used in the mid 80's. We have lots of large blisters (up to 40mm in diamet

Verstuurd vanaf mijn iPhone Begin doorgestuurd bericht: > Van: Steven Nieman <stefnieman@...> > > Onderwerp: #attackedbywhales #newboat WE SOLD THE BOAT! Now what??? Sailing Ocean F... > > Vanaf 6.12

after working more then 10 years without any problem, my furuno MFDBB black box stopped working. For a couple of days, I could restart it for a few minutes, but now no more signal after booting. Pocho

Danny, Have you noticed holes for wires and plumbing in the port and starboard outboard lower corners of the bulkhead going from the forward head and the forward hanging locker to the main cabin? Fair

It seems that upon close inspection, our 1991 Electrolux stove has finally given up. I hear Force 10 has nice options. Has anyone purchased one, and would you mind sharing the model? I do plan to swap

All, I have seen this part before, but I cannot remember what it is used for. Any advice is appreciated. The threaded hole is about 18 or 19mm. The OD of the part is about 50mm. CW Bill Rouse Amel Own

Question: can the stop solenoid be removed from the pump housing after removing the fuel load adjusting screw cover?. regards Steve s/v Dusk sm 378