|
sticky
How to do almost anything
#Wiki
All Group Members and Moderators, We have added a Amel Yacht Owners Group Wiki which can hopefully answer any of your questions regarding how to use the new group and its tools. When you are online at
All Group Members and Moderators, We have added a Amel Yacht Owners Group Wiki which can hopefully answer any of your questions regarding how to use the new group and its tools. When you are online at https://amelyachtowners.groups.io/g/main you will notice "Wiki" in the left column at the bottom. Click on Wiki to discover what you can do. The Wiki also includes a section for Moderators. Most of the content in this Wiki was provided by group.io, our host. I hope this helps you. -- Best, Bill Rouse Yacht School 720 Winnie St Galveston Island, TX 77550 +1(832) 380-4970 My Calendar
By CW Bill Rouse
·
|
|
sticky
ZOOM Meeting Technical Questions: 3 messages
#ZOOM
For those planning to attend the ZOOM meeting, please post questions to the Topic " ZOOM meeting technical questions" by replying to this email. Tilo Peters will likely respond to these technical ques
For those planning to attend the ZOOM meeting, please post questions to the Topic " ZOOM meeting technical questions" by replying to this email. Tilo Peters will likely respond to these technical questions. -- Best, CW Bill Rouse Amel Owners Yacht School ( http://amelownersyachtschool.com/ ) 720 Winnie St Galveston Island, TX 77550 +1(832) 380-4970 My Calendar ( https://preparetocastoff.blogspot.com/p/calendar.html )
By CW Bill Rouse
·
|
|
Intermittent starting issue 17 messages
For a couple of years I have had an issue ,where I turn the key and nothing happens, or the blower may come on and then turning the key further results in the blower going off. It seems to be a condit
|
For a couple of years I have had an issue ,where I turn the key and nothing happens, or the blower may come on and then turning the key further results in the blower going off. It seems to be a condit
|
By Patrick McAneny
·
|
|
Rocna 33 anchor- does it fits without modification on Super Maramu 2000 9 messages
Hello, after waking at 6 a clock in 30m of water and 200m from shore I have decided to stop fighting original Amel anchor. on my previous boat I had Delta and it was good for 17 years. After reading p
|
Hello, after waking at 6 a clock in 30m of water and 200m from shore I have decided to stop fighting original Amel anchor. on my previous boat I had Delta and it was good for 17 years. After reading p
|
By Slavko Despotovic
·
|
|
Seacock for aft head 13 messages
I need to replace my seacock in the aft head ,could someone confirm the size I need ,I believe it to be 1 1/4" NPT , but not sure and I want to purchase it prior to taking the old one out ,as my boat
|
I need to replace my seacock in the aft head ,could someone confirm the size I need ,I believe it to be 1 1/4" NPT , but not sure and I want to purchase it prior to taking the old one out ,as my boat
|
By Patrick McAneny
·
|
|
Volvo D3-110 Sensor - Spare Sensor Sets 10 messages
Dear Amelia’s Because our Volvo D3-110 is running with some sensors, I try to find out which of those are most important and vital to have as spare. I do have the D3-110 C and I’m quite happy with it,
|
Dear Amelia’s Because our Volvo D3-110 is running with some sensors, I try to find out which of those are most important and vital to have as spare. I do have the D3-110 C and I’m quite happy with it,
|
By Rudolf Waldispuehl
·
|
|
Engine overheating - Amel54 5 messages
Hi All, I've a problem with my engine D3-110i-C engine running hot (it has 1350hrs on the clock) I'm having to keep the rev's down at 1100RPM of less otherwise the engine temp steadily rises, so that
|
Hi All, I've a problem with my engine D3-110i-C engine running hot (it has 1350hrs on the clock) I'm having to keep the rev's down at 1100RPM of less otherwise the engine temp steadily rises, so that
|
By David Crisp
·
|
|
Good idea when changing head ball valve
I just found this. It may take some of the stress out of changing head ball-valves when in the water. Watch the video for the explanation on how to use. https://www.svb24.com/en/seabung-emergency-plug
|
I just found this. It may take some of the stress out of changing head ball-valves when in the water. Watch the video for the explanation on how to use. https://www.svb24.com/en/seabung-emergency-plug
|
By Mark Erdos
·
|
|
Running Rigging A54
Does anyone know the brand of the original running rigging on the A54 ? We like to renew some sheets but want to keep it as original as possible. Asked Maud at Amel but they don't provide this anymore
|
Does anyone know the brand of the original running rigging on the A54 ? We like to renew some sheets but want to keep it as original as possible. Asked Maud at Amel but they don't provide this anymore
|
By Laurens Vos
·
|
|
Leak on oil filter TMD22a 3 messages
We have a Volvo Penta TMD22a with a ‘remote’ oil filter. In the engine an adaptor piece has been mounted from which the hoses run to the filter cartridge. We strongly suspect this square shaped adapto
|
We have a Volvo Penta TMD22a with a ‘remote’ oil filter. In the engine an adaptor piece has been mounted from which the hoses run to the filter cartridge. We strongly suspect this square shaped adapto
|
By Herman Goverse
·
|
|
B&G HYDRA 2000 - Depth and Sonic Speed stopped working
The B&G depth and sonic speed have suddenly stopped working. Testing according to manual in Sonic speed unit seems to have correct values, so I am suspecting that the problem is the Depth Card in the
|
The B&G depth and sonic speed have suddenly stopped working. Testing according to manual in Sonic speed unit seems to have correct values, so I am suspecting that the problem is the Depth Card in the
|
By Andrew & Kate Lamb
·
|
|
Sliding ring seal of Calpeda pump 3 messages
Martin, If you are referring to the 12mm seal pictured below, yes, it is fairly standard. I bought several at a sidewalk shop in Penang, Malaysia. Just make sure it is made of stainless steel. Failure
|
Martin, If you are referring to the 12mm seal pictured below, yes, it is fairly standard. I bought several at a sidewalk shop in Penang, Malaysia. Just make sure it is made of stainless steel. Failure
|
By CW Bill Rouse
·
|
|
Is this a standard addition? 2 messages
Hello, We were wondering if anyone knows what this setup is, is it usual in a SM? It appears to have a Airmar transducer in it Thanks for your help -- Darren & Karen SM171 Tradewinds III Tasmania, Aus
|
Hello, We were wondering if anyone knows what this setup is, is it usual in a SM? It appears to have a Airmar transducer in it Thanks for your help -- Darren & Karen SM171 Tradewinds III Tasmania, Aus
|
By Darren Moore
·
|
|
Diesel heater install
Hello, We are looking at installing a Diesel heater to our 1996 Super Maramu Currently looking at a Wallas Spartan 4.5kw unit which has three in and out ports, we'd like to run a port to the Saloon, m
|
Hello, We are looking at installing a Diesel heater to our 1996 Super Maramu Currently looking at a Wallas Spartan 4.5kw unit which has three in and out ports, we'd like to run a port to the Saloon, m
|
By Darren Moore
·
|
|
D3-110 Starter Earthing Relay Part Number Request 12 messages
Hi folks, Today we launched Stella after almost 2 years on the hard. Tried to start the motor ... nogo! I believe I've traced the problem to the Earthing Relay whose job seems to be to momentarily con
|
Hi folks, Today we launched Stella after almost 2 years on the hard. Tried to start the motor ... nogo! I believe I've traced the problem to the Earthing Relay whose job seems to be to momentarily con
|
By Dean Gillies
·
|
|
Fuel Stick 14 messages
I broke my plastic fuel stick , I am thinking about making one from aluminum bar stock. Is there any reason that would be a problem to use in the fuel tank ? Thanks, Pat SM Shenanigans
|
I broke my plastic fuel stick , I am thinking about making one from aluminum bar stock. Is there any reason that would be a problem to use in the fuel tank ? Thanks, Pat SM Shenanigans
|
By Patrick McAneny
·
|
|
Main hatch 3 messages
Eric I encourage you to try my system with the spring on the outside of the bar applying it against the frame ! it is very easy to open , just tilt the bottom of the bar out of the groove , and let it
|
Eric I encourage you to try my system with the spring on the outside of the bar applying it against the frame ! it is very easy to open , just tilt the bottom of the bar out of the groove , and let it
|
By Nicolas Klene
·
|
|
Blisters under Orange Boot Stripe 5 messages
Hi all, I'm on the hard at the moment for bi-yearly maintenance and I've noticed that there are blisters on the orange boot stripe on the aft end of the boat. The yard manager here thinks it's definit
|
Hi all, I'm on the hard at the moment for bi-yearly maintenance and I've noticed that there are blisters on the orange boot stripe on the aft end of the boat. The yard manager here thinks it's definit
|
By Gerhard Hoffmann
·
|
|
Galley stove replacement 4 messages
Helllo Richard, Our Unold induction cook plate has suction cups and is very secure on our Corian counter top during very heavy weather. Otherwise, it resides on top of the gas burners and stays well i
|
Helllo Richard, Our Unold induction cook plate has suction cups and is very secure on our Corian counter top during very heavy weather. Otherwise, it resides on top of the gas burners and stays well i
|
By Germain Jean-Pierre
·
|
|
There is a spring on the companionway locking bar 7 messages
On the inboard side of the companionway there are two threaded bolts sticking out of it. Sitting on each bolt is a piece of stiff plastic tubing inside of a coil spring in the first photo attached . T
|
On the inboard side of the companionway there are two threaded bolts sticking out of it. Sitting on each bolt is a piece of stiff plastic tubing inside of a coil spring in the first photo attached . T
|
By eric freedman
·
|
